Set the lens iris level as desired with the joystick. The factory default setting is 10S. Dwell time changes as follows:. The factory default setting is 1. No scene file is selected at OFF. The setting menu appears. If you want to change these parameters, you must set them again. Select OFF if you are not using the home position function.
PT SR. Modes change as follows:. To set a panning starting point and panning endpoint. The panning speed increases when the joystick is moved to the right, and decreases when it is moved to the left.
Caution: If the panning range is changed after the camera has not panned for a long time or has been panning in the same panning range, the picture may not be clear or noise may appear.
In such cases, pan the camera fully several times. If this does not eliminate the problem, refer servicing to qualified service personnel. ON: The camera pans from the starting point to the endpoint, and keeps rotating in the same direction to return to the starting point. OFF: The camera pans from the starting point to the endpoint, and rotates backward to the starting point.
ON: Manual pan is limited from the starting point to the endpoint specified by position setting. ON: Limits the manual zoom operation by following the procedure below. The manual zoom operation is not available in the TELE direction beyond the settled zoom position. This is used for assigning one of the following auto functions to the AUTO key on the controller. Pressing the AUTO key activates the assigned function after this setting.
The image on the monitor screen is flipped horizontally and vertically at the tilt angle of approx. In case of moving the joystick to other directions, it does not function. Caution: For security, do not operate your VCR for recording while the password menus are displayed on the monitor. Though the entered password is not displayed, the up-arrow moves one character to the right. If a wrong password is entered, the screen returns to the verification menu.
Repeat steps to to verify the password. The screen returns to the verification menu. ON: Preset privacy zones are veiled on the monitor screen. Moving the joystick in the L direction decreases the zone frame, and moving it in the H direction increases it. However, the aspect ratio is fixed at 3 to 4. The privacy zone setting has been completed.
New settings are not registered. OFF: The speed is constant at the fastest level regardless of the zoom ratio. OFF: Area tittle does not appear. Factory default setting: OFF. A submenu appears except when OFF is selected. The origin of the direction North is set.
Note: Area titles are highlighted until the origin is set. Adjust the zoom or focus with the joystick. The area title position appears on the monitor screen. An area title always appears under the camera ID. If the camera ID and an area title are set to be shown in separate positions, the area title appears above the camera ID. The direction menu of the selected number appears. See page The selected character appears in the editing field and the blinking cursor moves one position to the right.
Repeat steps 1 and 2 until one area title is completed. The area title appears on the monitor screen. If the setting is different, they appear in the area title position. If two or more area numbers are set in the same position, the title of the highest number appears. PLAY: Stored operations are reproduced. A routine of manual operations can be stored for 1 minute at the maximum and reproduced repetitively. Set the following parameters for the patrol-learn starting position. These parameters are stored when the patrol-learn mode starts.
Operate patrol-learn manually. The operation data is stored. The countdown to complete learning is displayed. The camera turns to the starting point and reproduces the operations stored in the memory. Iris operation is valid only in the playback mode. Select patrol play in the setup menu, and then close the menu. The camera turns to the starting point and the operations stored in memory are reproduced. If this happens, re-enter the routine of manual operations for patrol-learn.
If an alarm input is received, the camera turns to a preset position, and sends an alarm output signal. The position number corresponds to the alarm input number , , and Two contact closure signals Open collector type are output through the Alarm Output connector.
Note: The shorter the duration, the more frequent will be the detection output. OFF: Contact closure signals are deactivated.
A motion. AUX 1 2 : An alarm signal is output when the camera receives a command from the controller. Note: It is recommended to set the connected external device to ignore the shorter alarm outputs of 90 ms or less from the camera. ON: The camera sends an alarm output signal after it turns to a preset position. ON: The contacts are cleaned for approx. Note: Select OFF when the camera downloads or uploads the preset data.
The electronic zoom magnifies a scene fold. With a fold optical zoom lens, the camera is capable of fold zoom. An alarm output is sent when the camera moves to the designated position depending on the mode.
The camera picture remains as a still image on the monitor screen until the camera reaches the preset position. This function is useful for surveillance via local area network. ON: The last displayed still image is shown till the camera finishes moving to a preset position. However, the still image may be distorted with the effect of panning or tilting.
OFF: The current image is being displayed while the camera is moving to a preset position. The camera setting menu appears. Follow the steps below to edit the camera ID characters. The selected character appears in the editing area. After editing the camera identification characters, follow the steps below to decide the position of. This function allows you to edit or correct a specific character.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the pres- ence of uninsulated "dangerous volt- age" within the product's enclosure that may be of sufficient magnitude to con- SA stitute a risk of electric shock to per- sons.
The exclamation point within an equi- lateral triangle is intended to alert the user to the presence of important oper- ating and maintenance servicing instructions in the literature accompa- nying the appliance. SA For U. The serial number of this product may be found on the top of the unit. Model No. A polarized plug has two blades with one wider than the other. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
SA 13 Unplug this apparatus during lightning storms or when unused for long periods of time. Digital Flip Operation q Tilting down w The picture is e Tilting down turned upside- down instantly around at degrees of the tilt angle.
In such cases, activate the refresh mode on the special 2 menu. To prevent electric shock, do not remove screws or covers. Afterwards, wipe off the remaining detergent with a dry cloth. Burn-in of an image may be caused on the fluorescent screen of CRT.
Consumables Parts having contacts such as the lens-drive motors, cooling fan motor and slip-rings inside the camera are subject to wear with time. Self-diagnosis Function If the camera continues operating abnormally for 30 seconds or more due to such an accident as external noise, the camera will automatically reset its power. Prevention of blooming and smear When the camera is aimed at a bright light source, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear.
Smear Bright object Environmental effects on imaging This unit is not equipped with a wiper, a visor, etc. Switches, keys and the joystick are used in the setup operations. Preset Menu P. Preset No. Setting P. Preset Setting Menu P. Password Verification P. Page 11 Position Setting P. Page 12 The keys switches to be used for setup are shown in the table below. The joystick on the connected controller may also be used for setup.
The table also shows the functions and the operations of the individual controllers. For details, see the manual for the controller to be used. See page 18 for the setting. For example, the pan-tilt speed slows down when the camera zooms in. See page 28 for details. Page 15 Generally, when a light from the background is too strong such as a spotlight, all objects except the main object in the picture are displayed darker because the lens iris is adjusted with respect to strong brightness.
This model ignores strong bright- ness by masking the source of the strong bright- ness, thereby the main object is displayed clearly. See page 40 for details. The preset setting menu appears on the monitor screen. Download the factory settings into the controller and upload the correct preset data newly to the initialized WV-CWA.
The factory default setting is OFF. Page Deleting Preset Positions See the pages below for the settings respectively. Select OFF if you are not using the home position function. Page 24 This determines the starting point and the cursor moves to END.
The manual zoom operation is not available in the TELE direction beyond the settled zoom position. A 3-digit number is used for a password to limit access to all settings. However, the aspect ratio is fixed at 3 to 4. Page 29 3. Page 31 3. OFF: The electronic zoom function is not used. The camera setting menu appears. When you select ALC, set backlight compensation.
Care should be taken not to scratch the dome cover when wiping it. You can adapt the camera to your requirements by setting up the respective items in these menus. Menus are built in a hierarchical structure, from the Setup menu at the top to Manual Mask Area Selection at the bottom. These menus are described on the following pages for reference prior to setup. Page 9 The keys switches to use for setup are shown in the table below.
The joystick on the connected con- troller may also be used for setup. The table also shows the functions versus the operations of the individ- ual controllers. For details, see the manual for the controller to be used.
See page 17 for the setting. After this setting, the AUTO key performs as assigned. Page 13 Note: The result of field setup of the mask area and level adjustment is fed back effected to the lens iris control in ALC mode. The color temperature range for the proper white balance is approx.
Proper white balance may not be obtained under the following conditions: 1. The preset setting menu appears on the monitor screen.
Page 17 3. Pan Offset If the camera is replaced with a new one, the pan offset function is used to adjust its positions to be the same as before except patrol setting. The system controller can download or upload the preset position data. The factory default setting is OFF. ON: Preset ID appears on the monitor screen.
The display position set menu appears. The factory default setting is 10S. Dwell time changes as follows: S stands for second s , and MIN stands for minute s. Modes change as follows: OFF: No automatic operation. The camera can be operated only manually. Page 23 5. ON: Manual pan is limited from the starting point to the end- point specified by position setting. Pressing the AUTO key activates the assigned function after this setting.
Page 26 3. Page 28 3. Adjust the zoom or focus by using the joystick. The area title position appears on the monitor screen. Operate patrol-learn manually.
0コメント